Discontinued and replaced by M2MSHD9-2S

The Addonics family of Combo mSATA HDD duplicator is designed for making multiple copies of mSATA SSD or 2.5" SATA HDD/SSD from a single master drive. Each duplicator comes bundled with a set of 2,5" mSATA flash drive kit that turns a mSATA SSD into a 2.5" SATA SSD. You can mix and match the mSATA SSD and the hard drive into the duplicator, thus making it a handy tool for transferring the content between the mSATA card and 2.5" hard drive. There is no computer needed or complex software to operate. Just open the doors on the drive bays, load the master media into the source bay and the target media of capacity equal or larger into the target bays, lock the drive doors and push the start button to start the copying process.

About this model

This 1:9 mSATA /SSD/HDD HS Duplicator PRO allows you to copy from one source media onto as many as nine (9) target media at one time. Comes bundled with ten (10) mSATA flash drive kits to convert mSATA SSD into a 2.5" SSD, the source and target drive can be of either mSATA SSD, 2.5" SATA SSD or 3.5" SATA hard drive. In addition, there is a source slot for using 3.5" hard drive as a master drive, a great solution for transferring content on 3.5" SATA hard drive to mSATA SSD or 2.5" SATA drive. By adding other optional 2.5" flash drive adapters, the supported media can be expanded to include M2 (NGFF) card, CFast card, CF card, slim SATA SSD and 1.8" HDD/SSD. Designed with snap-In drive bay, drives are easily added or removed without any special tool, just like an ordinary cassette tape.

Duplicator overview

Installing the mSATA SSD onto the 2.5" mSATA flash drive kit (also applies to mini mSATA SSD) 

The following Addonics optional 2.5" flash drive kits allow this duplicator to copy mSATA/mini mSATA, CFast, CF card or slim SATA SSD

(Shown with media side facing up)

note: the flash cards shown above are for illustration purpose and are not part of the flash drive adapter

Combo mSATA SSD / 2.5" HDD/SSD Duplicator family comparison chart

• Copy up to nine (9) mSATA/mini mSATA SSD or 2.5" SATA HDD/SSD with drive thickness up to 9.5 mm
• Supported source media: mSATA/mini SATA SSD, 2.5" SSD, 2.5" hard drive and 3.5" hard drive
• Supported target media: mSATA/mini SATA SSD. 2.5" SSD and 2.5" hard drive
• Comes with ten (10) units of mSATA flash drive kits (AD25MSD-E) to convert mSATA/mini mSATA SSD to 2.5" SSD
• An easy source switch at the back of the unit for selecting 3.5" drive or 2.5" drive source slot
• Additional support for M2 (NGFF), CFast, CF, slim SATA SSD and 1.8" HDD/SSD with the following optional 2.5" flash drive kit - AD25M2SSD-E, AD25CFASTD-N, AD25CFD-N, AA25SEMBK, AD18M25S
• High performance with minimum degradation from one to nine targets
• Typical copying speed^*:

• Support any file system
• Maximum storage capacity >3TB
• Source and Destination drives are added or removed like tape cartridges from each drive bay with no special tool required
• Drive sanitization:
  • SECURE ERASE - HDD duplicator sends a WIPE command to the hard drive. This command fills 00 string to entire HDD (this option may not be supported on some SSD or mSATA card)
  • OVERWRITE - One pass, 3 passes and 7 passes 5220.22-M. The duplicator writes a string of pattern over the entire disk one time, three times or seven times. 5220.22-M is the DoD standard for drive sanitization
• LCM control module provides a rich set of robust advanced configuration options (diagram of duplicator features can be here Full LCD console feature list)
• Operate as a stand alone appliance. No computer or software needed

* The speed here is for reference only. The actual transfer rate varies depending on the speed of the source and destination drive

Components for the main unit
Storage Tower (ST9), 1:9 HDD High Speed Duplicator subsystem (HDU9SASHS), five (5) Snap-In Double Drive (AE25SNAP2SA), one 3.5" Snap-In SATA Mobile Rack II (AESNMRS)

Bundled accessories: ten (10) units of 2.5" mSATA flash drive kit (AD25MSD), power cord, user guide

• Writing mode: Sector to Sector
• Typical copying speed: 

• Sturdy metal frame construction
• Drives are added or removed just like VHS cassette without tools
• LCD display with functional control panel
• Well ventilated for efficient air flow.
• Two low noise high CFM ball bearing cooling fan
• Integrated universal AC 110/240V power supply
• Dimension: ~ 7.5 x 17.25 x 17.2 in. (90 x 438 x 437 mm.)
• Weight: ~ 23.93 lb (10.85 Kg)
  
• Operating temperature and humidity: 0 - 50 degree C, 15% - 90% RH
• Storage temperature and humidity: (-20) - (65) degree C, 0% - 95% RH non-condensing

Specification subject to change without notice