1:4 M2 / mSATA / 2.5" HDD/SSD Duplicator PRO

The Addonics family of  M2 / mSATA / 2.5" HDD/SSD duplicator is designed for making multiple copies of M2 SSD, mSATA SSD or 2.5" SATA HDD/SSD from a single master drive. Each duplicator comes bundled with a set of 2,5" M2 / mSATA flash drive kit that turns an M2 SSD or mSATA SSD into a 2.5" SATA SSD. You can mix and match the M2 SSD, mSATA SSD and the 2.5" hard drive into the duplicator, thus making it a handy tool for transferring the content between the M2 SSD, mSATA card and 2.5" HDD/SSD. There is no computer needed or complex software to operate. Just open the doors on the drive bays, load the master media into the source bay and the target media of capacity equal or larger into the target bays, lock the drive doors and push the start button to start the copying process.

 

About this model

This 1:4 mSATA /SSD/HDD HS Duplicator PRO allows you to copy from one source media onto as many as four (4) target media at one time. Comes bundled with five (5) M2/mSATA flash drive kits to convert either an M2 SATA SSD or mSATA SSD into a 2.5" SSD. The target and source drive can be of either an M2 SATA SSD, mSATA SSD or 2.5" SATA HDD/SSD. In addition, there is a source slot for using a 3.5" hard drive as a master drive, a great solution for transferring content from a 3.5" SATA hard drive to M2 SATA SSD, mSATA SSD or 2.5" SATA HDD. By adding other optional 2.5" flash drive adapters, the supported media can be expanded to include CFast card, CF card, slim SATA SSD and 1.8" HDD/SSD. Designed with snap-In drive bay, drives are easily added or removed without any special tool, just like an ordinary cassette tape.

 

Front view   Rear view

   


Installing the M2 SATA SSD onto the 2.5" M2/mSATA flash drive kit 

2.5 CF Flash drive

 


Installing the mSATA card onto the 2.5" M2/mSATA flash drive kit


The following Addonics optional 2.5" flash drive kit can be used for duplicating CFast , CF card, slim SATA SSD or 1.8"  drive.

Show with media side facing up

CFast card in 2.5" CFast
drive kit (AD25CFASTD-N)

CF card in 2.5" CF drive kit
(AD25CFD-N)

Slim SATA SSD 2.5" HDD
adapter (AA25SEMBK)

1.8" micro SATA - 2.5" SATA
HDD adapter (AD18M25S

note: the flash cards shown above are for illustration purpose and are not part of the flash drive adapter

  • Copy up to four (4) of the following type of media: M2 SATA SSD, mSATA/mini mSATA SSD or 2.5" SATA HDD/SSD with drive thickness up to 9.5 mm
  • Supported source media: M2 SATA SSD, mSATA/mini SATA SSD, 2.5" SSD, 2.5" hard drive and 3.5" hard drive
  • Comes with five (5) units of M2/mSATA flash drive kits (AD25M2MSA) to convert M2 SATA SSD or mSATA SSD to 2.5" SATA SSD
  • An easy source switch at the back of the unit for selecting 3.5" HDD or 2.5" HDD as the source slot
  • Drives are loaded/unload without any special tool
  • Additional support for CFast, CF, slim SATA SSD and 1.8" HDD/SSD with the following optional 2.5" flash drive kit -  AD25CFASTD-NAD25CFD-NAA25SEMBKAD18M25S
  • Maximum copying speed ~ 120MB/sec with no performance degradation from increased loading
  • Support any file system
  • No known drive capacity limitation
  • Source and Destination drives are added or removed like tape cartridges from each drive bay with no special tool required
  • Drive sanitization:
    • SECURE ERASE - HDD duplicator sends a WIPE command to the hard drive. This command fills 00 string to entire HDD (this option may not be supported on some SSD or mSATA card)
    • OVERWRITE - One pass, 3 passes, and 7 passes 5220.22-M. The duplicator writes a string of pattern over the entire disk one time, three times or seven times. 5220.22-M is the DoD standard for drive sanitization
  • LCM control module provides a rich set of robust advanced configuration options (diagram of duplicator features can be here Full LCD console feature list)
  • Operate as a stand-alone appliance. No computer or software needed

* The speed here is for reference only. The speed was measured basing on using 2.5" SATA III 250 GB hard drive for both source and target. The transfer rate varies depending on the speed of the source and destination drive.

  • Writing mode: Sector to Sector
  • Maximum copying speed up to 120 MB/sec. Actual performance depends on the speed of the drive.
  • Sturdy metal frame construction
  • Snap-In Disk Array for quick insertion or removal of drive without a special tool
  • LCD display with a functional control panel
  • Well ventilated for efficient air flow.
  • Low noise high CFM ball bearing cooling fan
  • Integrated 340W 110/240V AC/DC power supply
  • Dimensions (W x D x H): 7.5 x 16 x 10.4 inch (190 x 406 x 264 mm)
  • Weight: 17.2 lb (8.8 Kg)
  • Operating temperature and humidity: 0 - 60 degree C, 15% - 90% RH
  • Storage temperature and humidity: (- 20) - (65) degree C, 0% - 95% RH non-condensing

PRODUCTS

M2S25HD4H-2S - (1:4 M2 / mSATA / 2.5" HDD/SSD Duplicator PRO)
Content: 1:4 M2 / mSATA / 2.5" HDD/SSD Duplicator PRO main unit, five (5) 2.5" M2 / mSATA SSD flash drive kits (AD25M2MSA), power cord, user guide
Price: 899.00

ACCESSORIES

AD25CFASTD-N (2.5" CFast HDD kit, open end, black )
Content: 2.5" CFast hard drive kit with open end black color bracket for easy media nstallation, user guide.
Price: 24.95
AD25CFD-N (2.5" CF HDD PRO, easy media insertion and removal, black color)
Content: 2.5" CF hard drive kit with black color bracket and open end for easy media installation.
Price: 26.95
AD18M25S (1.8" micro SATA - 2.5" SATA HDD adapter)
Content: 1.8" micro SATA - 2.5" SATA HDD adapter,
Price: 19.00
AA25SEMBK (Slim SATA SSD 2.5" HDD adapter)
Content: 2.5" HDD adapter kit for slim SATA embedded SSD, user guiode
Price: 19.00
AD25M2MSA (2.5" M2 / mSATA Flash drive kit)
Content: 2.5" M2 / mSATA flash drive kit with easy media installation or removal design (black color), user guide
Price: 27.95