1:3 M2/mSATA/ 2.5" SSD/HDD HS Duplicator

The Addonics family of Combo M2 and mSATA HDD duplicator is designed for making multiple copies of M2 SATA SSD, mSATA SSD or 2.5" SATA HDD/SSD from a single master drive. Each duplicator comes bundled with a set of 2,5" M2/mSATA flash drive kit that turns an M2 SATA SSD or mSATA SSD into a 2.5" SATA SSD. You can mix and match the M2, mSATA SSD and the hard drive into the duplicator, thus making it a handy tool for transferring the content between the M2 SATA SSD, mSATA SSD, and 2.5" HDD/SSD. There is no computer needed or complex software to operate. Just open the doors on the drive bays, load the master media into the source bay and the target media of capacity equal or larger into the target bays, lock the drive doors and push the start button to start the copying process.

 

This 1:3 M2/mSATA/ 2.5" SSD/HDD HS Duplicator makes copies from one to three (3) drives at one time with a mix of any M2 SATA SSD, mSATA SSD or 2.5" HDD/SSD at speed up to 120 MB/sec. Drives are loaded directly into the duplicator with no special tools required. Comes bundled with four (4) 2.5" M2/mSATA drive kits, either the M2 or mSATA SSD is loaded into the duplicator just like a standard 2.5" hard drive. By adding different optional 2.5" flash drive kits, this duplicator can also copy other flash cards such as CFast card, CF card, micro SATA drive or slim SATA drive.

Front view
(Drive insertion and removal illustration)


Rear view

 

Installing the M2 SATA SSD onto the 2.5" M2/mSATA flash drive kit 

2.5 CF Flash drive

 


Installing the mSATA card onto the 2.5" M2/mSATA flash drive kit


The following Addonics optional 2.5" flash drive kit can be used for duplicating CFast , CF card, slim SATA SSD or 1.8"  drive.

Show with media side facing up

CFast card in 2.5" CFast
drive kit (AD25CFASTD-N)

CF card in 2.5" CF drive kit
(AD25CFD-N)

Slim SATA SSD 2.5" HDD
adapter (AA25SEMBK)

1.8" micro SATA - 2.5" SATA
HDD adapter (AD18M25S

note: the flash media shown above are for illustration purpose and are not part of the flash drive adapter

  • Duplicates up to three (3) M2 SATA SSD¹, mSATA SSD or 2.5" HDD/SSD at one time
  • Great for cloning M2 SATA SSD, mSATA SSD or 2.5" HDD/SSD, system upgrade, transferring content among these drives or for data distribution
  • Includes four (4) units M2/mSATA flash drive kits (AD25M2MSA) and one eSATA cable for daisy chaining
  • Supported media - M2 SATA SSD, mSATA SSD, 2.5" HDD/SSD
  • Maximum speed up to 120 MB/sec., with no performance degradation regardless of the number of targets
    *Actual speed depends on the performance of the media
  • Maximum drive thickness up to 9.5 mm.
  • Supports any type of file systems using sector to sector copy
  • Can be set up to copy data only for the following supported file systems:
    • Windows FAT 16/32, exFAT, NTFS
    • Linux: Ext 2/3/4,
    • Mac: HFS/HFS/HFSX
  • Maximum drive size >4TB
  • Drive sanitizing:
    • Quick ERASE - remove data and partition table only. Data may still be recoverable using special software.
    • Full ERASE - HDD duplicator sends a WIPE command to the hard drive. This command fills 00 string to entire HDD
    • DoD ERASE - overwrites a string of pattern over the entire disk three times according to DoD 5220.22-M sanitizing standard
  • The LCM control module provides a rich set of robust advanced configuration options (click Full LCD console feature list to see a complete list of this duplicator functions)
  • Operate as a stand-alone appliance. No computer or software needed
  • Optional adapters for duplicating the following flash media: CFast card, CF card, slim SATA SSD, 1.8" micro SATA HDD/SSD

Note
The speed here is for reference only. The speed was measured basing on using high-performance mSATA SSD for both source and target. The transfer rate varies depending on the speed of the source and destination drive 

1  There are three types of M2 SSD: M2 SATA SSD, M2 PCIe SSD, and M2 NVMe SSD. M2 SATA SSD uses SATA interface, the same interface on SATA hard drive, and is the only type of M2 media supported by this duplicator.

  • Writing mode: Sector to Sector
  • Support maximum drive thickness up to 9.5 mm.
  • Maximum copying speed up to 120MB/sec. Actual speed varies depending on the drive performance
  • Powerful 32-bit CRC checksum to assure data integrity
  • Sturdy metal frame construction
  • Four (4) Snap-In drive bay for easy drive insertion or removal with no special tool
  • LCD display with functional control panel
  • Well ventilated for efficient air flow.
  • Low noise high CFM ball bearing cooling fan
  • Integrated 340W 110/240 auto-sense power supply
  • Dimensions (W x D x H): 7.48 x 10.63 x 6.5 inch (190 x 270 x 16.5 mm)
  • Weight: ~ 9.38 lb (5.25 Kg)
  • Operating temperature and humidity: 0 - 60 degree C, 15% - 90% RH
  • Storage temperature and humidity: (- 20) - (65) degree C, 0% - 95% RH non-condensing

PRODUCTS

M2S25HFD3H - (1:3 M2 / mSATA / 2.5" HDD/SSD Duplicator)
Content: 1:3 M2 / mSATA /2.5" HDD/SSD Duplicator main unit, four 2.5" M2/mSATA flash drive kit (AD25M2MSA), power cord, quick user guide, HS Duplicator Controller user manual.
Price: 759.00

ACCESSORIES

AD25CFASTD-N (2.5" CFast HDD kit, open end, black )
Content: 2.5" CFast hard drive kit with open end black color bracket for easy media nstallation, user guide.
Price: 24.95
AD25CFD-N (2.5" CF HDD PRO, easy media insertion and removal, black color)
Content: 2.5" CF hard drive kit with a half open-end black color bracket for easy media installation.
Price: 26.95
AD18M25S (1.8" micro SATA - 2.5" SATA HDD adapter)
Content: 1.8" micro SATA - 2.5" SATA HDD adapter,
Price: 19.00
AA25SEMBK (Slim SATA SSD 2.5" HDD adapter)
Content: 2.5" HDD adapter kit for slim SATA embedded SSD, user guiode
Price: 19.00
AD25M2MSA (2.5" M2 / mSATA Flash drive kit)
Content: 2.5" M2 / mSATA flash drive kit with easy media installation or removal design (black color), user guide
Price: 27.95